• Wet wipes Nonwoven Jet Tunnel dryer
  • Wet wipes Nonwoven Jet Tunnel dryer
  • Wet wipes Nonwoven Jet Tunnel dryer
  • Wet wipes Nonwoven Jet Tunnel dryer
  • Wet wipes Nonwoven Jet Tunnel dryer
  • Wet wipes Nonwoven Jet Tunnel dryer

Wet wipes Nonwoven Jet Tunnel dryer

Model No.︰

TM-IR4m-jet

Brand Name︰

tamprinter

Country of Origin︰

China

Unit Price︰

US $ 17000 / set

Minimum Order︰

1 set

Share on:

Product Description

 

Nonwoven Jet Tunnel dryer

 Warning

              Please read this operation manual carefully before working

 

Content

1     Safety instruction. 3

1.1      Safety regulation. 4

1.2      Warning signs (figure/photo) 5

1.3      The interpretation of signs 6

2     Specification. 7

2.1      Machine function and feature. 8

2.2      Machine's model and nameplate. 8

2.3      Specification table. 11

2.4      Machine noise value. 12

2.5      Main partsfigure... 12

2.6      Machine dimensionfigure... 13

2.7      Circuit diagram . 13

3     Installation. 15

3.1      Transit safety item.. 15

3.2      Transit method. 15

3.3      Installing place selection. 16

3.4      Installation method/(picture) 16

3.5      Installation and level adjustment 17

3.6      Power source requirement 17

3.7      Exterior power source connection. 18

3.8      Power source inspection. 18

4     Operation. 19

4.1      Operation position(figure) 19

4.2      Operation panel instruction. 19

4.3      Emergence stop. 20

4.4      Operation precedure. 20

4.5      Machine adjustment 21

5     Maintenance. 23

5.1      Machine dayweekyear maintenance. 23

5.2      Machine lubrication. 25

5.3      Machine malfunction and handling. 25

6     Machine waste disposal 26

7     Safety and protection. 27

2         Specification

  1. machine’s working principle & function and feature

Working principle:

Hot air furnace blowing hot air so that non-woven moisture evaporation.

Dry hot stove in the electronics, food, pharmaceutical, printing, packaging, cleaning, heat treatment ... ... the industry has a very wide range of applications.

Function and feature:

  1. Dry hot stove with stainless steel heating pipe heating air for hot air, clean and sanitary, in line with environmental protection..
  2. Multi-fiber insulation cotton insulation, the use of safe and reliable, long-term high temperature work.
  3. Standard type of hot air fan application patented design of the cooling device, air volume adjustment using VDF speed, more energy saving, high controllability, heat loss and other excellent features.
  4. Equipped with double overheating overload protection device, fully guarantee the safety of equipment. Set the thermocouple outlet, direct detection, the outlet temperature.
    1. Model and machine nameplate
  1. Specification table

Model Parameter

TM-IR4m-jet

Tunnel Width(mm)

650

Power(P/V/Hz)

3/380/50

Heat pipeKW

3pcs*6kwX 2Group=36

VDF powerW

1.5KW*2PCS

Total powerKW

40

Tunnel DimensionL*W*H

4050*1010*1680

Electric box L*W*Hmm

600*600*960

Weight(kg)

580

NoteAll specification, dimension and design will not change if there is not any notice.

 

 

3         Installation

 

3.1       Transit safety item

1.  During transiting (moving or loading and unloading vehicles), machine should be moved by fork-lift and kept the balance. Carry it by carriage or container.

2.  Use the enough load capability fork-lift to transit machine.

  1. When move the machine, you can ask others to lead the ways and watch the safety.

4.  During transitingit should avoid collision and bad weather. And pay attention to protect the machine’ surface painting from damaging. When need to save the machine temporarily, please place it in a dry and room temperature environment. 

5.  The fork lift must be driven by the experienced driver.

6.  The equipment can be moved by push. But be caution the speed.

7.  As the installation position plan, choose the proper installation position, and notice to keep enough distance with the surrounding barrier.

8.  When install the machine, the machine’s longitudinal and transverse level can be adjusted by the adjusting screw at four corners.

9.  If the equipment is damaged or short of parts, please don’t run it.

 

3.2 Transit method

1Machine can be moved by fork lift.

2Fork lift should insert the bottom of the machine.

3Keep the balance of machine when moving it.

3.3  Installing place selection

Please run the machine in follow situation

Environment

Environment

temperature

-1045no ice cover

Environment

humidity

Bellow 90%RHno dew

Save temperature

-20~+65

Environment

In room

(No causticityflammable gaspaint dust)

Altitude height

Below 1000m

 

3.4  Installation method/figure

 When installing the machine, there must be more than 1.5 m distance between the wall and machine. 3m spaces also have to be left for equipment operation.

 

3.5  Installation and level adjustment

Install this machine in the solid state reinforced concrete, and excess space can be used to place the work piece .When machine installed in the correct place, you can adjust machine longitudinal and transverse level by the adjusting screw at four corners.

 

3.6   Power source requirement

If the power source’ voltage is not enough, it will affect the motor’s output and the controller’s function.

It is very important to use the correct voltage to connect the machine and the power source. And only use the independent power source.

 

3.7   Exterior power source connection

Before connect the power source wire, you must make sure whether the machine voltage is the same as factory’ power source voltage.

Connect the wire to L1 L2 L3 NPE.

After connected the wire, make sure it is connected on the right Joints (figure)

Machine must be correct grounding so as to prevent from electric shock. Machine should be operated by the qualified electrician.

 

3.8   Power source inspection

   

 

Power Switch                                      power source switch

 

1After connect the power sourceit is very necessary to check whether the wire are  connect to the joints correct.

2 Rotate main switch on electric controller.

3 open the electrical control box, try to change three phase L1L2L3 sequence, Check whether the electrical source’ three phase wires are connected correct. Phase sequence indicator  LED Light Up is OK

 If not, exchange any two wires connection of three phase line L1, L2, L3.

4.  Above operation should be operated by the qualified electrician.

 

4.      Operation

4.1Operation position (figure)

4.2   Operation panel instruction

 

 

 

4.3  Emergency stop

 

During the machine running, if there are any abnormal function occurred; press this button to stop all movement. When resume of this button, first switches all vdf at the min position.

 

4.4  Operational procedures

Figure  1                             

               

1Before the first start-up, machinery should be checked whether grounding, then user should pay attention to check whether the grounding line remains firmly grounded everyday.

2Before start-up , the protective covers and protective doors should be closed, or

choose to use tape to seal the leaky mouth AIR pipe to avoiding workshop temprature raise.

3First turn power switch to the right (Figure 1), the main power lines in electronic

control box are connected, and fan starts to work..

4Periodically check the electrical wiring for circuit phenomenon.10Adjust the belt tension on both sides to prevent the belt running to the false way.

5Having good hygiene, to prevent dust.

6If there is an imminently hazardous situation, immediately turn off the main power switch, to avoid further accidents.

 



Payment Terms︰ TT / LC

Product Image