Inert material UV primer dryer with Automatic belt correction structure

Inert material UV primer dryer with Automatic belt correction structure

Model No.︰TM- 3DUV -1

Brand Name︰tamprinter

Country of Origin︰China

Unit Price︰US $ 7000 / set

Minimum Order︰1 set

Inquire Now

Product Description

Inert material UV primer dryer

Parameter:

 

Belt Width  550mm
Conveyor belt Stainless Conveyor belt Stainless
Temperature in oven about 65 Celsius
Maximum speed 3~ 12m/min
Power 380V/50HZ/3P 12Kw
UV Lamp 3KW*4 lamp=12kw
Machine Size 2400*1020*2080mm about 6CBM
Machine net Weight 650kg

 

Conveyor belt Stainless SUS304

From the top, 4 directions slanting down, shining, no lights at the bottom

Top Air Draft Motor 1 pcs

Top Blower Motor 1pcs

Conveyor Motor 1pcs

Exhausamp 2KW*4pcs e Pipe Diameter: 200mm

If Clean room, oven inside about 65 celsius

Lamp Lifetime about 1000 hours

Application nylon + fiber, PET, EVA,PP glass, ceramic, etc.

Plywood Packing

Payment Terms T/T , LC,OA

Stock :20sets color Red ,white or blue random delivery

UV primer =Silicone modified compounds 

 

Inert material,Usually EVA Outsole /Mould Outsole surface treatment passes this UV tunnel machine, which is conducive to the next step of glue paste。

 

UV surface can be adhered without sanding, adhesion is promoted to all kinds of hard-to-adhere materials (such as: nylon + fiber, PET, PP glass, ceramic, etc.), especially for all kinds of metal (such as: tin, aluminum alloy , Vacuum coating, stainless steel, stainless steel chrome plating, stainless steel anodic treatment / oxidative coloring / sandblasting / drawing) and other surface adhesion. Resistant to boiled and salt spray.

 

Coating process: material surface cleaning and dust removal → processing agent filter spray → infrared preheating or natural placement 2 ~ 5min → UV coating spray coating → UV curing → inspection → finished product.

 

In order to ensure the tension between the EVA, IP, PHYLON midsole and the rubber outsole or upper material, it is necessary to do water washing and UV irradiation treatment before the sole is added or formed (EVA does not need to be washed)
Water washing: The function of water washing is to wash off the chemical residues such as release agent/release agent on the surface of IP and PHYLON, so that it can more fully interact with the treatment agent. There are three procedures for washing: 1. Over alkaline liquid PH 10.5~11.5, temperature 55±5℃; 2. Neutral water cleaning PH 6~8, temperature 45±5℃; 3. Acidic liquid PH 2.5~3.5, temperature 55 ±5°C. It takes about 5-6 minutes to complete the washing process. During the washing process, the side that needs to be attached to IP and PHYLON should face down so that they can fully contact with the washing liquid. After washing with water, directly pass through the oven (the far right end of the picture below, the temperature is 50℃) to dry IP and PHYLON.

UV irradiation: UV irradiation is required after washing with water. You need to wipe the cleanser first, fully clean it, and open the pores on the surface. After drying in an oven at 50±5℃ for 2 minutes, then wipe the UV treatment agent. The role of the treatment agent is to "anchor", fill in small pores, and change the affinity of the material surface for better adhesion to the glue. The treatment agent needs to be dried in an oven at 50±5°C for 2 minutes. Then directly into the UV irradiation, UV irradiation can trigger a polymerization reaction to increase the polarity of the sole, enhance the viscosity and adhesion, and make the sole easier to stick. If not irradiated, insufficiently irradiated, or expired, the pull force value is low and can be easily pulled by hand. (Please note that glue cannot directly adhere to the IP and upper).

Payment Terms︰ TT / LC

Product Image